- whatsapp +51955515985
- support@ecuforcetruck.com
- 24/7 Customer Support
Menu
Shop
Account
Subtotal: $0.00
No products in the cart.
Circuit Description
The ECM monitors the NOx concentration in the engine’s exhaust gases using an aftertreatment intake NOx sensor and aftertreatment outlet NOx sensor. By comparing these two values, the ECM is able to determine the conversion efficiency of the SCR catalyst and dosing system. Critically low NOx conversion efficiency is an indication of a missing SCR catalyst.
Component Location
The SCR catalyst is located in the vehicle’s exhaust system, after the diesel particulate filter and decomposition tube.
Conditions for Running the Diagnostics
This diagnostic has to meet specific engine and aftertreatment conditions to run and complete. NOx sensor data is gathered over varying engine speeds and loads. When enough data has been gathered, the diagnostic will run, make a pass/fail decision, and begin to gather data again.
Conditions for Setting the Fault Codes
The ECM has detected that the NOx conversion efficiency of the SCR catalyst is critically low.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or the Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails for two consecutive trips.
Diesel exhaust fluid injection into the aftertreatment system is disabled.
Engine torque will be reduced if the engine is operated for a limited period of time with the fault code active.
Engine torque will be severely reduced and vehicle speed will be limited to 8 km [5 mi] per hour after extended engine operation with the fault code active.
Conditions for Clearing the Fault Code
After completing a stationary regeneration (as instructed in this fault code troubleshooting tree) and no additional faults become active, the repair has been validated. Note that this fault code will still be active
It is necessary to use the “Reset All Faults” command in INSITE? electronic service tool to clear this fault and extinguish the amber CHECK ENGINE lamp and/or MIL
Shop Talk
Troubleshoot all other active NOx sensor and SCR dosing system related fault codes before this fault.
Possible causes of this fault include:
Incorrect calibration revision on INCAL? CD
Tampering with SCR catalyst system, removal of SCR catalyst from vehicle, or malfunctioning SCR catalyst
Malfunctioning diesel exhaust fluid dosing system
Exhaust system leaks
Degraded, diluted, or incorrect diesel exhaust fluid
Diesel exhaust fluid deposits in decomposition tube.
This fault code can be set as a result of multiple failure modes. All steps of the troubleshooting tree must be completed.
Reference the appropriate OEM wiring diagram when troubleshooting circuits that utilize wiring supplied by the OEM.
For intermittent power supply and datalink communication issues with Aftertreatment Components, it is highly recommended that the OEM Power Distribution Center fuses and relays be thoroughly checked for loose, missing or intermittent connections.
Possible Cause:
1) Aftertreatment NOx sensor failure
2) Aftertreatment DEF dosing unit Filter failure
3) Aftertreatment SCR catalyst failure
4) ECM calibration
Related
Categories Cumminz, DTC TRUCKS, ISX12 CM2250 (2010-12)Tags 2010-12, 31, 3151, 4794, Aftertreatment, Catalyst, CM2250, Code, Condition, Cummins, Exists, Fault, FMI, ISX12, Missing-, MR, PID, SCR, SPN, System
Wiring Diagrams
Component Locators
- VOLVO PTT TECH TOOL 2.8.220 2023 Last version 1pc
Trucks software$200.00
Rated 0 out of 5
- Volvo PROSIS Offline 2019 Parts Catalog Installation Service
Trucks software$45.00
Rated 0 out of 5
- Volvo Penta EPC 6 Offline VMware [12.2021] VMware
Trucks software$64.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRON 108-118-128
Trucks software$38.00
Rated 0 out of 5
- Wabco ToolBox plus 13.7.0.1 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software$84.00
Rated 0 out of 5
- Cat Factory Password Generator 1.0 2019 WINDOWS 10
CAT$55.00
Rated 0 out of 5
- Navkal 2018 offline version remove DPF MAXXFORCE 13 EPA 10
Navistar$80.00
Rated 0 out of 5
- CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT$45.00
Rated 0 out of 5
- Navistar Engine Diagnostics (NEDS) Software 2023
Navistar$96.00
Rated 0 out of 5
- HINO EPC 2018 TRUCKS / BUSES 2018 EPC PARTS CATALOG
Hino$85.00
Rated 0 out of 5
- Magic Tuner Flash Tool v2.1
Magic Tuner$180.00
Rated 0 out of 5
- Wabco Diagnostic Software 2021 (Tebs-E 6.01) + PINS
Trucks software$60.00
Rated 0 out of 5
- Meritor Wabco Tool Box 12.9.1
Trucks software$35.00
Rated 0 out of 5
Scania$30.00
Rated 0 out of 5
- JPRO 2023 v3 diagnostic software latest version
JPRO$100.00
Rated 0 out of 5
- Detroit Diesel Drumroll Engineering 7.06 DDDE v7.06
Detroit$20.00
Rated 0 out of 5
- download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi$76.00
Rated 0 out of 5
- download MANCATS II v14.01 2014 Diagnostic software MAN CATS ( virtual machine )
MAN$75.00
Rated 0 out of 5
- Magic Tuner [paccar, Maxxforce, Detroit, Caterpillar, Delete]
Magic Tuner$50.00
Rated 0 out of 5
- Wabco ToolBox plus 13.7.0.1 + ECAS CAN2 v3.00 Diagnostics Software
Trucks software$84.00
Rated 0 out of 5
Related products
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- PACCAR PX-9 CM2350 (2013-17) Fault Code:3634 PID: SPN:5484 FMI:4 Engine Fan Clutch 2 Control Circuit – Voltage Below Normal or Shorted to Low Source
DTC TRUCKS
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- SERVICE MANUAL DAF Workshop Manual DD DF DT Series
DAF$20.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 863 sms
BOBCAT$62.00
Rated 0 out of 5
- SERVICE MANUAL Carrie Metrobird TDS 115
CARRIE$25.00
Rated 0 out of 5
- SERVICE MANUAL MACK V-MAC IV (2004 Emissions)
MACK$29.00
Rated 0 out of 5
INTERNATIONAL ENGINES$34.00
Rated 0 out of 5
- SERVICE MANUAL HINO FD.FE.FF.SG 2008
HINO$34.00
Rated 0 out of 5
- SERVICE MANUAL I2017 International® A26 Engine
INTERNATIONAL ENGINES$24.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 1600 sms
BOBCAT$30.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 610-611 sms
BOBCAT$45.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 630-631-632 sms
BOBCAT$45.00
Rated 0 out of 5